IKE Encryption Algorithm
with AH Transport/Tunnel mode (HOST)
[IP][AH]
[IP1][AH][IP2]

[Interoperability Test Scenario]

Last Update: February 23, 2001

This scenario verifies interoperability when the target HOST is attached to the model network.

• Subjects:

Verification of host's action.
IKE with IPsec Authentication Header transport mode.

• Verification Points
  

  Parameter		Value
  IKE	Encryption Algorithm	DES
  		3DES
  		rijndeal(128bit)

• Fixed Parameters
  

Parameter		Value
IKE	Exchange mode	Main mode
	Authentication method	Pre-Shared key (DH group 1)
	Phase-1 lifetime	24 hour
	Phase-2 lifetime	24 hour
	Hash Algorithm	MD5
IPsec	Authentication algorithm	HMAC-MD5
	MODE	Transport
	Granularity	Host

• Physical Network Configuration:

  (3ffe:501:481d:f002::11) (3ffe:501:481d:f002::12)
         HOST-2                  HOST-3
           |(HIF-2y)               |(HIF-3y)
           |                       |
(Net-y)  --+-----------+-----------+-- (3ffe:501:481d:f002::/64)
                       |
                       |(I/F-y) (3ffe:501:481d:f002::1)
                    ROUTER-1
                       |(I/F-z) (3ffe:501:481d:f001::1)
                       |
(Net-z)      ----+-----+------------- (3ffe:501:481d:f001::/64)
                 |
                 |(HIF-1z) (3ffe:501:481d:f001::11)
               HOST-1
        

Network	Prefix	Network media
Net-y	3ffe:501:481d:f002::/64	Ethernet 10BASE-T
Net-z	3ffe:501:481d:f001::/64	Ethernet 10BASE-T

• Test Machine:

Machine	Comments	Initial status	Configuration
HOST-3	Reference Machine	Is attached to Net-y with power turned off.	-
HOST-2	Reference Machine	Is attached to Net-y with power turned off.	-
ROUTER-1	Reference Machine	Power is turned off.  I/F-z is attached to Net-z while I/F-y is attached to Net-y.	Sends RA to Net-z and Net-y.
HOST-1	Target Machine	Is attached to Net-z with power turned off.	-

• Configuration list:
  
  *DH Key = Diffie-Hellman shared key
  *Hash Alg = IKE Authentication Algorithm
  *Enc Alg = IKE Encryption Algorithm
  *PH1 Lifetime = Phase-1 Lifetime
  *PH2 Lifetime = Phase-2 Lifetime
  *Protocol = Security Protocol
  *AH auth = AH Authentication Algorithm
  *Auth Method = Authentication Method
  *Upper = Upper Layer Protocol
  

No.

Machine

Src

Dest

IKE

IPsec

Exchange mode

Local ID

Remote ID

Auth Method

DH Key

Hash Alg

Enc Alg

PH1 Lifetime

PH2 Lifetime

Protocol

Mode

AH auth

Upper

1

HOST-1

HIF-1z

HIF-2y

Main

3ffe:501:481d:f001::11

3ffe:501:481d:f002::11

DH(1)

IKE-TEST

MD5

DES

24 Hour

24 Hour

AH

Transport

HMAC-MD5

any

HOST-2

HIF-2y

HIF-1z

Main

3ffe:501:481d:f002::11

3ffe:501:481d:f001::11

DH(1)

IKE-TEST

MD5

DES

24 Hour

24 Hour

AH

Transport

HMAC-MD5

any

2

HOST-1

HIF-1z

HIF-2y

Main

3ffe:501:481d:f001::11

3ffe:501:481d:f002::11

DH(1)

IKE-TEST

MD5

3DES

24 Hour

24 Hour

AH

Transport

HMAC-MD5

any

HOST-2

HIF-2y

HIF-1z

Main

3ffe:501:481d:f002::11

3ffe:501:481d:f001::11

DH(1)

IKE-TEST

MD5

3DES

24 Hour

24 Hour

AH

Transport

HMAC-MD5

any

3

HOST-1

HIF-1z

HIF-2y

Main

3ffe:501:481d:f001::11

3ffe:501:481d:f002::11

DH(1)

IKE-TEST

MD5

rijndeal

24 Hour

24 Hour

AH

Transport

HMAC-MD5

any

HOST-2

HIF-2y

HIF-1z

Main

3ffe:501:481d:f002::11

3ffe:501:481d:f001::11

DH(1)

IKE-TEST

MD5

rijndeal

24 Hour

24 Hour

AH

Transport

HMAC-MD5

any

4

HOST-1

HIF-1z

HIF-2y

Main

3ffe:501:481d:f001::11

3ffe:501:481d:f002::11

DH(1)

IKE-TEST

MD5

DES

24 Hour

24 Hour

AH

Tunnel

HMAC-MD5

any

HOST-2

HIF-2y

HIF-1z

Main

3ffe:501:481d:f002::11

3ffe:501:481d:f001::11

DH(1)

IKE-TEST

MD5

DES

24 Hour

24 Hour

AH

Tunnel

HMAC-MD5

any

5

HOST-1

HIF-1z

HIF-2y

Main

3ffe:501:481d:f001::11

3ffe:501:481d:f002::11

DH(1)

IKE-TEST

MD5

3DES

24 Hour

24 Hour

AH

Tunnel

HMAC-MD5

any

HOST-2

HIF-2y

HIF-1z

Main

3ffe:501:481d:f002::11

3ffe:501:481d:f001::11

DH(1)

IKE-TEST

MD5

3DES

24 Hour

24 Hour

AH

Tunnel

HMAC-MD5

any

6

HOST-1

HIF-1z

HIF-2y

Main

3ffe:501:481d:f001::11

3ffe:501:481d:f002::11

DH(1)

IKE-TEST

MD5

rijndeal

24 Hour

24 Hour

AH

Tunnel

HMAC-MD5

any

HOST-2

HIF-2y

HIF-1z

Main

3ffe:501:481d:f002::11

3ffe:501:481d:f001::11

DH(1)

IKE-TEST

MD5

rijndeal

24 Hour

24 Hour

AH

Tunnel

HMAC-MD5

any

• Applications:

  ping program (ping)
  
  NOTE: 
  We select these applications, as typical application for each protocol  (ICMP/UDP/TCP).
  In this scenario, it is not a subject to verify each application in detail.

• Interoperability check

No	Action	Criteria	Comments
Address auto configuration check.
1	Boot ROUTER-1.	-	-
2	Boot HOST-1.	-	-
3	Boot HOST-2.	-	-
4	Boot HOST-3.	-	-
Availability confirmation.
5	At HOST-2, run "ping" to HOST-1.  Repeat 10 times, with 64 bytes ICMP payload, interval 1 second. Ex) # ping6 -s 64 -i 1 -c 10 HOST-1	*HOST-2 sends ICMP Echo Request to HOST-1. *HOST-2 receives ICMP Echo Reply from HOST-1.	HOST-2 and HOST-1 don't use IPsec.
6	At HOST-3, run "ping" to HOST-1.  Repeat 10 times, with 1452 bytes ICMP payload, interval 1 second. Ex) # ping6 -s 64 -i 1 -c 10 HOST-1	*HOST-3 sends ICMP Echo Request to HOST-1. *HOST-3 receives ICMP Echo Reply from HOST-1.	HOST-3 and HOST-1 don't use IPsec.
IPsec transport [IP][AH] (IKE Encryption algorithm=DES)
11	At HOST-1 set configuration #1	-	-
12	At HOST-2 set configuration #1	-	-
13	At HOST-2, run "ping" to HOST-1.  Repeat 20 times, with 64 bytes ICMP payload, interval 1 second. Ex) # ping6 -s 64 -i 1 -c 20 HOST-1.	*HOST-2 sends ICMP Echo Request to HOST-1. *HOST-2 receives ICMP Echo Reply from HOST-1. *AH is attached to original packet between HOST-1 and HOST-2.	AH transport between HOST-1 and HOST-2.(HMAC-MD5) HOST-2 <-> HOST-1 (ICMP)
14	At HOST-3, run "ping" to HOST-1.  Repeat 20 times, with 64 bytes ICMP payload, interval 1 second. Ex) # ping6 -s 64 -i 1 -c 20 HOST-1.	*HOST-3 sends ICMP Echo Request to HOST-1. *HOST-3 receives ICMP Echo Reply from HOST-1. *Original packets go through between HOST-1 and HOST-3.	HOST-3 and HOST-1 don't use IPsec.
IPsec transport [IP][AH] (IKE Encryption algorithm=3DES)
15	At HOST-1 set configuration #2	-	-
16	At HOST-2 set configuration #2	-	-
17	At HOST-2, run "ping" to HOST-1.  Repeat 20 times, with 64 bytes ICMP payload, interval 1 second. Ex) # ping6 -s 64 -i 1 -c 20 HOST-1.	*HOST-2 sends ICMP Echo Request to HOST-1. *HOST-2 receives ICMP Echo Reply from HOST-1. *AH is attached to original packet between HOST-1 and HOST-2.	AH transport between HOST-1 and HOST-2.(HMAC-MD5) HOST-2 <-> HOST-1 (ICMP)
18	At HOST-3, run "ping" to HOST-1.  Repeat 20 times, with 64 bytes ICMP payload, interval 1 second. Ex) # ping6 -s 64 -i 1 -c 20 HOST-1.	*HOST-3 sends ICMP Echo Request to HOST-1. *HOST-3 receives ICMP Echo Reply from HOST-1. *Original packets go through between HOST-1 and HOST-3.	HOST-3 and HOST-1 don't use IPsec.
IPsec transport [IP][AH] (IKE Encryption algorithm=Rijndeal)
19	At HOST-1 set configuration #3	-	-
20	At HOST-2 set configuration #3	-	-
21	At HOST-2, run "ping" to HOST-1.  Repeat 20 times, with 64 bytes ICMP payload, interval 1 second. Ex) # ping6 -s 64 -i 1 -c 20 HOST-1.	*HOST-2 sends ICMP Echo Request to HOST-1. *HOST-2 receives ICMP Echo Reply from HOST-1. *AH is attached to original packet between HOST-1 and HOST-2.	AH transport between HOST-1 and HOST-2.(HMAC-MD5) HOST-2 <-> HOST-1 (ICMP)
22	At HOST-3, run "ping" to HOST-1.  Repeat 20 times, with 64 bytes ICMP payload, interval 1 second. Ex) # ping6 -s 64 -i 1 -c 20 HOST-1.	*HOST-3 sends ICMP Echo Request to HOST-1. *HOST-3 receives ICMP Echo Reply from HOST-1. *Original packets go through between HOST-1 and HOST-3.	HOST-3 and HOST-1 don't use IPsec.
IPsec tunnel [IP][AH][IP] (IKE Encryption algorithm=DES)
23	At HOST-1 set configuration #4	-	-
24	At HOST-2 set configuration #4	-	-
25	At HOST-2, run "ping" to HOST-1.  Repeat 20 times, with 64 bytes ICMP payload, interval 1 second. Ex) # ping6 -s 64 -i 1 -c 20 HOST-1.	*HOST-2 sends ICMP Echo Request to HOST-1. *HOST-2 receives ICMP Echo Reply from HOST-1. *AH is attached to original packet between HOST-1 and HOST-2.	AH tunnel between HOST-1 and HOST-2.(HMAC-MD5) HOST-2 <-> HOST-1 (ICMP)
26	At HOST-3, run "ping" to HOST-1.  Repeat 20 times, with 64 bytes ICMP payload, interval 1 second. Ex) # ping6 -s 64 -i 1 -c 20 HOST-1.	*HOST-3 sends ICMP Echo Request to HOST-1. *HOST-3 receives ICMP Echo Reply from HOST-1. *Original packets go through between HOST-1 and HOST-3.	HOST-3 and HOST-1 don't use IPsec.
IPsec tunnel [IP][AH][IP] (IKE Encryption algorithm=3DES)
27	At HOST-1 set configuration #5	-	-
28	At HOST-2 set configuration #5	-	-
29	At HOST-2, run "ping" to HOST-1.  Repeat 20 times, with 64 bytes ICMP payload, interval 1 second. Ex) # ping6 -s 64 -i 1 -c 20 HOST-1.	*HOST-2 sends ICMP Echo Request to HOST-1. *HOST-2 receives ICMP Echo Reply from HOST-1. *AH is attached to original packet between HOST-1 and HOST-2.	AH tunnel between HOST-1 and HOST-2.(HMAC-MD5) HOST-2 <-> HOST-1 (ICMP)
30	At HOST-3, run "ping" to HOST-1.  Repeat 20 times, with 64 bytes ICMP payload, interval 1 second. Ex) # ping6 -s 64 -i 1 -c 20 HOST-1.	*HOST-3 sends ICMP Echo Request to HOST-1. *HOST-3 receives ICMP Echo Reply from HOST-1. *Original packets go through between HOST-1 and HOST-3.	HOST-3 and HOST-1 don't use IPsec.
IPsec tunnel [IP][AH][IP] (IKE Encryption algorithm=Rijndeal)
31	At HOST-1 set configuration #6	-	-
32	At HOST-2 set configuration #6	-	-
33	At HOST-2, run "ping" to HOST-1.  Repeat 20 times, with 64 bytes ICMP payload, interval 1 second. Ex) # ping6 -s 64 -i 1 -c 20 HOST-1.	*HOST-2 sends ICMP Echo Request to HOST-1. *HOST-2 receives ICMP Echo Reply from HOST-1. *AH is attached to original packet between HOST-1 and HOST-2.	AH tunnel between HOST-1 and HOST-2.(HMAC-MD5) HOST-2 <-> HOST-1 (ICMP)
34	At HOST-3, run "ping" to HOST-1.  Repeat 20 times, with 64 bytes ICMP payload, interval 1 second. Ex) # ping6 -s 64 -i 1 -c 20 HOST-1.	*HOST-3 sends ICMP Echo Request to HOST-1. *HOST-3 receives ICMP Echo Reply from HOST-1. *Original packets go through between HOST-1 and HOST-3.	HOST-3 and HOST-1 don't use IPsec.

Mark"*"with no number means that we are going to judge that subject.